Allied-air-enterprises 506271-01 User Manual download pdf

506271-01 Page 1 of 14Issue 0921

Save these instructions for future reference

INSTALLATION INSTRUCTIONS

RPGE/RGE Series

Gas Heating/Electric Cooling Package Unit

Do not store combustible materials, including gasoline

and other flammable vapors and liquids, near the furnace,

vent pipe, or warm air ducts. Such actions could cause

property damage, personal injury, or death.

WARNING

Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage.

Refer to this manual. For assistance or additional information, consult a qualified installer, service agency,

or the gas supplier.

WARNING

Never use a flame to check for gas leaks. Explosion

causing injury or death may occur.

WARNING

If this unit is to be installed in a mobile or manufactured

home application, the ductwork must be sized to achieve

static pressures within the manufacturer’s guidelines. All

other installation guidelines must also be followed. Failure

to do so may result in equipment damage, personal injury,

and improper performance of the unit.

WARNING

The installation of the furnace, wiring, warm air ducts, venting, etc. must conform to the requirements of the National Fire

Protection Association; the National Fuel Gas Code, ANSI Z223.1 (latest edition) and the National Electrical Code, ANSI/

NFPA No. 70 (latest edition) in the United States; the Canadian Installation Codes CAN/CGA-B149.1 & .2 (latest edition)

and the Canadian Electrical Code Part 1, CSA 22.1 (latest edition) in Canada; and any state or provincial laws, local

ordinances, or local gas utility requirements. Local authorities having jurisdiction should be consulted before installation

is made. Such applicable regulations or requirements take precedence over the general instructions in this manual.

CAUTION

Manufactured By

Allied Air Enterprises, Inc.

A Lennox International Company

215 Metropolitan Drive

West Columbia, SC 29170

TABLE OF CONTENTS

INSTALLATION ...................................... 2

START-UP .............................................. 8

OPERATION ........................................ 10

Cooling System............................... 10

Heating System............................... 10

MAINTENANCE ....................................11

CONTROL SYSTEM DIAGNOSTICS .. 12

WIRING DIAGRAM .............................. 13

*506271-01*

1 2 3 4 5 6 ... 13 14

Summary of Contents

Page 1 - RPGE/RGE Series

506271-01 Page 1 of 14Issue 0921Save these instructions for future referenceINSTALLATION INSTRUCTIONSRPGE/RGE SeriesGas Heating/Electric Cooling Pac

Page 2 - INSTALLATION

Page 10 of 14 506271-01Issue 09217. After reassembly of all parts is complete and all wiresare reconnected, open the main manual gas shutoff valve;c

Page 3 - CAUTION

506271-01 Page 11 of 14Issue 092110-second interval, then the ignition control will de-energize the gas valve.6. The ignition control is designed t

Page 4 - Vent Cover

Page 12 of 14 506271-01Issue 0921BurnersTo clean the burners, first remove them from the furnace asexplained in Burner Instructions on page 9. Vacu

Page 5

506271-01 Page 13 of 14Issue 0921Wiring Diagram – Single PhaseFigure 8

Page 6

Page 14 of 14 506271-01Issue 0921NOTES

Page 7

Page 2 of 14 506271-01Issue 0921INSTALLATIONThese instructions must be hung on or near the furnace in aconspicuous place.These furnace units are sin

Page 8 - START-UP

506271-01 Page 3 of 14Issue 0921In the U.S., units may be installed on combustible floorsmade from wood or class A, B, or C roof covering material.I

Page 9

Page 4 of 14 506271-01Issue 0921Minimum horizontal clearance of 4' from electric meters, gasmeters, regulator, and relief equipment is required

Page 10 - OPERATION

506271-01 Page 5 of 14Issue 0921The supply and return air duct systems should be designedfor the CFM and static requirements of the job. They shoul

Page 11 - WARNING

Page 6 of 14 506271-01Issue 0921Gas piping recommendations:• A drip leg and a ground joint union must be installed inthe gas piping. A ground joint

Page 12

506271-01 Page 7 of 14Issue 0921All wiring should be done in accordance with theNational Electrical Code, ANSI/NFPA No. 70 (latestedition); Canadian

Page 13 - Wiring Diagram – Single Phase

Page 8 of 14 506271-01Issue 0921START-UPPre-Start Check ListComplete the following checks before starting the unit:1. Check the type of gas being su

Page 14

506271-01 Page 9 of 14Issue 0921Manifold Gas Pressure Adjustment Regulator – NaturalGasFor purpose of input adjustment, the minimumpermissible gas s

Comments to this Manuals

No comments

Allied-air-enterprises 506271-01 User Manual

Browse online or download User Manual for Grills Allied-air-enterprises 506271-01. Allied Air Enterprises 506271-01 User Manual

Summary of Contents

Comments to this Manuals